{"status":"ok","message-type":"work","message-version":"1.0.0","message":{"indexed":{"date-parts":[[2025,8,2]],"date-time":"2025-08-02T18:05:56Z","timestamp":1754157956659,"version":"3.41.2"},"reference-count":11,"publisher":"Emerald","issue":"2","license":[{"start":{"date-parts":[[2003,5,1]],"date-time":"2003-05-01T00:00:00Z","timestamp":1051747200000},"content-version":"tdm","delay-in-days":0,"URL":"https:\/\/www.emerald.com\/insight\/site-policies"}],"content-domain":{"domain":[],"crossmark-restriction":false},"short-container-title":[],"published-print":{"date-parts":[[2003,5,1]]},"abstract":"<jats:p>The purpose of this study was to compare costs and dimensional control parameters between same geometry parts obtained by same prototyping techniques using different material moulds. Vacuum casting was used to obtain prototypes of a three\u2010blade helix of a motor boat propeller. Aluminium and room temperature vulcanising (RTV) rubber moulds were manufactured and tested within the study. Manufacturing costs and dimensional control parameters were used within the comparison study. For the dimensional deviation performance factor used, no significant differences were observed relatively to the dimensional control parameters measured. However, the average deviations were smaller for the RTV rubber mould prototype.<\/jats:p>","DOI":"10.1108\/13552540310467121","type":"journal-article","created":{"date-parts":[[2003,8,8]],"date-time":"2003-08-08T06:52:40Z","timestamp":1060325560000},"page":"111-115","source":"Crossref","is-referenced-by-count":13,"title":["Vacuum casting with room temperature vulcanising rubber and aluminium moulds for rapid manufacturing of quality parts: a comparative study"],"prefix":"10.1108","volume":"9","author":[{"given":"A.M.","family":"Ramos","sequence":"first","affiliation":[]},{"given":"C.","family":"Relvas","sequence":"additional","affiliation":[]},{"given":"J.A.","family":"Simo\u02dces","sequence":"additional","affiliation":[]}],"member":"140","reference":[{"unstructured":"Balsmeier, P.W. and Voisin, W.J. (1997), \u201cRapid prototyping: state\u2010of\u2010art manufacturing\u201d, Industrial Management, Vol. 39 No. 1, pp. 1\u20134.","key":"key2022012920260975400_b1"},{"unstructured":"Braglia, M. and Petroni, A. (1999), \u201cA management\u2010support technique for the selection of rapid prototyping technologies\u201d, Journal of Industrial Technology, Vol. 15 No. 4, pp. 1\u20136.","key":"key2022012920260975400_b2"},{"unstructured":"Chen, D. and Cheng, F. (1999), \u201cIntegration of product and process development using rapid prototyping and workcell simulation technologies\u201d, Journal of Industrial Technology, Vol. 16 No. 1, pp. 1\u20136.","key":"key2022012920260975400_b3"},{"unstructured":"Chua, C.K. and Leong, K.F. (1997), Rapid Prototyping: Principles and Applications in Manufacturing, Wiley, London.","key":"key2022012920260975400_b4"},{"unstructured":"Folkestad, J.E. and Johnston, R.L. (2001), \u201cResolving the conflict between design and manufacturing: integrated rapid prototyping and rapid tooling (IRPRT)\u201d, Journal of Industrial Technology, Vol. 17 No. 4, pp. 1\u20137.","key":"key2022012920260975400_b5"},{"unstructured":"Kochan, D. and Chua, C.K. (1995), \u201cState\u2010of\u2010art and future trends in advanced rapid prototyping and manufacturing\u201d, International Journal of Information Technology, Vol. 1 No. 2, pp. 173\u201384.","key":"key2022012920260975400_b6"},{"unstructured":"Kress, H. (1996), \u201cIntegration factors within a virtual prototyping environment\u201d, International Journal of Flexible Automation and Integrated Manufacturing, Vol. 1 No. 4, pp. 29\u201343.","key":"key2022012920260975400_b7"},{"doi-asserted-by":"crossref","unstructured":"Ramos, A.M., Relvas, C. and Sim\u00f5es, J.A. (2003), \u201cThe effect of milling strategies on texture, roughness and dimensional deviations of machined surfaces\u201d, Journal of Materials Processing Technology, (in press).","key":"key2022012920260975400_b8","DOI":"10.1016\/S0924-0136(03)00160-2"},{"unstructured":"Rehg, J.K. (1994), Computer Integrated Manufacturing, Prentice\u2010Hall, Englewood Cliffs, NJ.","key":"key2022012920260975400_b9"},{"unstructured":"Smith, P.G. and Reinertsen, D.G. (1998), Developing Products in Half the Time, Von Nostrand Reinhold, New York.","key":"key2022012920260975400_b10"},{"unstructured":"Swanstrom, K.A. (1999), Engineers don't operate in a vacuum, Design News (On\u2010line), http:\/\/www.manufacturing.net\/magazine\/dn\/archives\/1999\/dn0705.99\/guest.html","key":"key2022012920260975400_b11"}],"container-title":["Rapid Prototyping Journal"],"original-title":[],"language":"en","link":[{"URL":"https:\/\/www.emerald.com\/insight\/content\/doi\/10.1108\/13552540310467121\/full\/xml","content-type":"application\/xml","content-version":"vor","intended-application":"text-mining"},{"URL":"https:\/\/www.emerald.com\/insight\/content\/doi\/10.1108\/13552540310467121\/full\/html","content-type":"unspecified","content-version":"vor","intended-application":"similarity-checking"}],"deposited":{"date-parts":[[2025,7,25]],"date-time":"2025-07-25T00:28:41Z","timestamp":1753403321000},"score":1,"resource":{"primary":{"URL":"http:\/\/www.emerald.com\/rpj\/article\/9\/2\/111-115\/369184"}},"subtitle":[],"short-title":[],"issued":{"date-parts":[[2003,5,1]]},"references-count":11,"journal-issue":{"issue":"2","published-print":{"date-parts":[[2003,5,1]]}},"alternative-id":["10.1108\/13552540310467121"],"URL":"https:\/\/doi.org\/10.1108\/13552540310467121","relation":{},"ISSN":["1355-2546"],"issn-type":[{"type":"print","value":"1355-2546"}],"subject":[],"published":{"date-parts":[[2003,5,1]]}}}