{"status":"ok","message-type":"work","message-version":"1.0.0","message":{"indexed":{"date-parts":[[2026,3,11]],"date-time":"2026-03-11T04:31:22Z","timestamp":1773203482014,"version":"3.50.1"},"reference-count":31,"publisher":"MDPI AG","issue":"3","license":[{"start":{"date-parts":[[2020,3,17]],"date-time":"2020-03-17T00:00:00Z","timestamp":1584403200000},"content-version":"vor","delay-in-days":0,"URL":"https:\/\/creativecommons.org\/licenses\/by\/4.0\/"}],"content-domain":{"domain":[],"crossmark-restriction":false},"short-container-title":["Symmetry"],"abstract":"<jats:p>Cutter rings form an integral part of tunnel boring machines (TBM). These cutters are deployed in various hard rock tunneling projects. The life of the cutter rings governs the economics of tunneling significantly. This paper presents a novel methodology to enhance hardness and wear resistance of used worn out disc cutters in TBM for eco-friendly reuse. Disc cutters are mainly made of H13 tool steel. To improve the hardness and wear resistance, a layer of tungsten carbide is coated on the used cutter rings. Considering the long operating hours of TBM, cutter rings get worn out due to severe interaction with the hard rock both in compression and rolling mode. Replacement of the cutter-ring is costly, and quite a time consuming and cumbersome job. Refurbishment is always a better option and laser cladding is a novel technique for enhanced life of cutters. It increases the hardness and wear resistance of the cutters to a considerable extent. Cladding is carried out with the help of a laser beam. In this method, a layer of nanoparticles of tungsten carbide powder is deposited on the worn-out surface of the cutters. For carrying out the investigation, different coating parameters are selected based on the central composite design (CCD). With different capacities of laser, a total of 13 samples were prepared at various scanning speeds varying between 200 to 300 mm\/min and a level of laser power varying between 100 to 200 W. The coating is critically inspected by various means such as an optical microscope, FESEM, and EDS. Hardness testing was accomplished by Vicker\u2019s hardness testing machine. Wear testing was carried out with the aid of pin on disc setup. The results shows an asymmetrical behavior between the yield parameters (hardness and wear rate) and process parameters (scanning speed and laser power). The hardness values increased from 16% to 95%. A correlation test was conducted between the hardness and wear rate. The results depict a clear negative correlation between them, indicating the advantage of laser coating for reducing cutter ring wear in TBM.<\/jats:p>","DOI":"10.3390\/sym12030471","type":"journal-article","created":{"date-parts":[[2020,3,20]],"date-time":"2020-03-20T07:29:07Z","timestamp":1584689347000},"page":"471","update-policy":"https:\/\/doi.org\/10.3390\/mdpi_crossmark_policy","source":"Crossref","is-referenced-by-count":21,"title":["A Novel Method of Laser Coating Process on Worn-Out Cutter Rings of Tunnel Boring Machine for Eco-Friendly Reuse"],"prefix":"10.3390","volume":"12","author":[{"ORCID":"https:\/\/orcid.org\/0000-0002-4490-6555","authenticated-orcid":false,"given":"Anil Kumar","family":"Agrawal","sequence":"first","affiliation":[{"name":"Indian Institute of Technology (Indian School of Mines), Dhanbad 826004, India"}]},{"ORCID":"https:\/\/orcid.org\/0000-0002-6814-7936","authenticated-orcid":false,"given":"Somnath","family":"Chattopadhyaya","sequence":"additional","affiliation":[{"name":"Indian Institute of Technology (Indian School of Mines), Dhanbad 826004, India"}]},{"given":"V. M. S. R.","family":"Murthy","sequence":"additional","affiliation":[{"name":"Indian Institute of Technology (Indian School of Mines), Dhanbad 826004, India"}]},{"ORCID":"https:\/\/orcid.org\/0000-0001-8973-5035","authenticated-orcid":false,"given":"Stanis\u0142aw","family":"Legutko","sequence":"additional","affiliation":[{"name":"Institute of Mechanical Engineering, Poznan University of Technology, 61-704 Poznan, Poland"}]},{"ORCID":"https:\/\/orcid.org\/0000-0002-2967-1719","authenticated-orcid":false,"given":"Grzegorz","family":"Krolczyk","sequence":"additional","affiliation":[{"name":"Department of Manufacturing Engineering and Automation Products, Opole University of Technology, 45-758 Opole, Poland"}]}],"member":"1968","published-online":{"date-parts":[[2020,3,17]]},"reference":[{"key":"ref_1","doi-asserted-by":"crossref","first-page":"1","DOI":"10.1016\/j.tust.2016.05.010","article-title":"Tunnel boring machines (TBMs) in difficult grounds","volume":"57","author":"Due","year":"2016","journal-title":"Tunn. Undergr. Space Technol."},{"key":"ref_2","first-page":"65","article-title":"Assessment of abrasiveness for research of rock cutting","volume":"17","author":"Krepelka","year":"2012","journal-title":"Acta Montan. Slovaca"},{"key":"ref_3","doi-asserted-by":"crossref","first-page":"88","DOI":"10.1108\/13552540410526962","article-title":"Selective laser sintering and cladding of single-component metal powders","volume":"10","author":"Tolochko","year":"2004","journal-title":"Rapid Prototyp. J."},{"key":"ref_4","doi-asserted-by":"crossref","first-page":"154","DOI":"10.1016\/S0924-0136(00)00790-1","article-title":"Structure of laser cladded tungsten carbide composite coatings","volume":"109","author":"Kusin","year":"2001","journal-title":"J. Mater. Process. Technol."},{"key":"ref_5","doi-asserted-by":"crossref","first-page":"161","DOI":"10.1016\/0043-1648(93)90236-F","article-title":"Coarse cemented WC particle ceramic-metal produced by laser cladding composite coatings","volume":"170","author":"Beidi","year":"1993","journal-title":"Wear"},{"key":"ref_6","doi-asserted-by":"crossref","first-page":"46","DOI":"10.1016\/j.optlastec.2017.06.006","article-title":"Development of TiN particulates reinforced SS316 based metal matrix composite by direct metal laser sintering technique and its characterization","volume":"97","author":"Hussain","year":"2017","journal-title":"Opt. Laser Technol."},{"key":"ref_7","doi-asserted-by":"crossref","first-page":"222","DOI":"10.1016\/j.wear.2018.05.012","article-title":"Tool wear monitoring in rock drilling applications using vibration signals","volume":"408\u2013409","author":"Klaic","year":"2018","journal-title":"Wear"},{"key":"ref_8","doi-asserted-by":"crossref","first-page":"5553","DOI":"10.1016\/j.apsusc.2008.07.198","article-title":"Laser cladding of tungsten carbides (Spherotene\u00ae) hardfacing alloys for the mining and mineral industry","volume":"255","author":"Amado","year":"2009","journal-title":"Appl. Surf. Sci."},{"key":"ref_9","doi-asserted-by":"crossref","first-page":"11","DOI":"10.1016\/S0043-1648(01)00624-X","article-title":"Materials selection to excavator teeth in mining industry","volume":"250","author":"Vijande","year":"2001","journal-title":"Wear"},{"key":"ref_10","doi-asserted-by":"crossref","unstructured":"Amado, J.M., Tobar, M.J., and Y\u00e1\u00f1ez, A. (2010). Laser cladding of NiCr-WC metal matrix composites: Dependence on the matrix composition. Proceedings of the 36th International MATADOR Conference, Springer.","DOI":"10.1007\/978-1-84996-432-6_102"},{"key":"ref_11","first-page":"247","article-title":"Laser cladding of tungsten carbide powder","volume":"17","author":"Cadenas","year":"1997","journal-title":"WIT Trans. Eng. Sci."},{"key":"ref_12","first-page":"1077","article-title":"Influence of cutting parameters and conditions onto surface hardness of duplex stainless steel after turning process","volume":"20","author":"Krolczyk","year":"2013","journal-title":"Teh. Vjesn."},{"key":"ref_13","first-page":"425","article-title":"Laser Cladding of Ceramic and Metallic Coatings on Steel","volume":"47","author":"Ramous","year":"1990","journal-title":"Key Eng. Mater."},{"key":"ref_14","doi-asserted-by":"crossref","first-page":"661","DOI":"10.1007\/s13369-015-1726-6","article-title":"Analysis of contact phenomena and heat exchange in the cutting zone under minimum quantity cooling lubrication conditions","volume":"41","author":"Maruda","year":"2016","journal-title":"Arab. J. Sci. Eng."},{"key":"ref_15","doi-asserted-by":"crossref","first-page":"109","DOI":"10.1016\/j.wear.2017.09.020","article-title":"Experimental study on wear behaviors of TBM disc cutter ring under drying, water and seawater conditions","volume":"393","author":"Zhang","year":"2017","journal-title":"Wear"},{"key":"ref_16","doi-asserted-by":"crossref","first-page":"159","DOI":"10.1016\/j.optlaseng.2018.01.015","article-title":"Processing and characterization of laser sintered hybrid B 4 C\/cBN reinforced Ti-based metal matrix composite","volume":"105","author":"Gupta","year":"2018","journal-title":"Opt. Lasers Eng."},{"key":"ref_17","doi-asserted-by":"crossref","first-page":"25","DOI":"10.1016\/j.measurement.2018.10.047","article-title":"Effect of shielding gas on the plasma plume in pulsed laser welding","volume":"134","author":"Xu","year":"2019","journal-title":"Measurement."},{"key":"ref_18","doi-asserted-by":"crossref","first-page":"9982","DOI":"10.1016\/j.matpr.2017.06.306","article-title":"Development of reinforced TiN-SS316 metal matrix composite (MMC) using direct Metal laser sintering (DMLS) and its characterization","volume":"4","author":"Mandal","year":"2017","journal-title":"Mater. Today Proc."},{"key":"ref_19","doi-asserted-by":"crossref","first-page":"1470","DOI":"10.1016\/j.measurement.2012.11.034","article-title":"Application of the central composite design in optimization of machining parameters in drilling hybrid metal matrix composites","volume":"46","author":"Rajmohan","year":"2013","journal-title":"Measurement"},{"key":"ref_20","doi-asserted-by":"crossref","first-page":"134","DOI":"10.1016\/S0043-1648(98)00266-X","article-title":"Application of EDS peak enhancement ratios for compositional analysis of microstructures evolved during sliding wear","volume":"221","author":"Lepper","year":"1998","journal-title":"Wear"},{"key":"ref_21","unstructured":"Montgomery, D.C. (2013). Introduction to Statistical Quality Control, Wiley. [7th ed.]."},{"key":"ref_22","first-page":"6","article-title":"Effect of laser power on the microstructure and microhardness property of hybrid fabricated Ti6A14V based metal matrix composite","volume":"2224","author":"Franklin","year":"2016","journal-title":"Lect. Notes Eng. Comput. Sci."},{"key":"ref_23","first-page":"325","article-title":"Influence of Scanning Speed on Microstructure and Properties of Ni Based Laser Cladding Coating","volume":"38","author":"Qiu","year":"2009","journal-title":"Rare Met. Mater. Eng."},{"key":"ref_24","unstructured":"Ibrahim, M.Z., Kuo, T., Yusof, F., and Hamdi, M. (2017, January 19\u201321). Influence of Laser Power and Scanning Speed on the Hardness and Microstructure of Fe-Based Metallic Glass Coating on Nickel-Free Stainless Steel Substrate. Proceedings of the International Symposium on Novel and Sustainable Technology, Tainan City, Taiwan."},{"key":"ref_25","doi-asserted-by":"crossref","first-page":"331","DOI":"10.1016\/j.jmatprotec.2006.12.053","article-title":"Laser deposited TiC\/H13 tool steel composite coatings and their erosion resistance","volume":"186","author":"Jiang","year":"2007","journal-title":"J. Mater. Process. Technol."},{"key":"ref_26","doi-asserted-by":"crossref","first-page":"4579","DOI":"10.1007\/s40430-017-0734-8","article-title":"Effect of laser power and welding speed on microstructure and mechanical properties of fibre laser-welded Inconel 617 thin sheet","volume":"39","author":"Kumar","year":"2017","journal-title":"J. Braz. Soc. Mech. Sci. Eng"},{"key":"ref_27","doi-asserted-by":"crossref","first-page":"214","DOI":"10.1016\/j.wear.2007.10.001","article-title":"Taguchi method applied to parametric appraisal of erosion behavior of GF-reinforced polyester composites","volume":"265","author":"Mahapatra","year":"2008","journal-title":"Wear"},{"key":"ref_28","doi-asserted-by":"crossref","first-page":"128","DOI":"10.17531\/ein.2016.1.17","article-title":"Wear characteristics and defects analysis of friction stir welded joint of aluminium alloy 6061-T6","volume":"18","author":"KumAR","year":"2016","journal-title":"Eksploat. i Niezawodn."},{"key":"ref_29","doi-asserted-by":"crossref","first-page":"707","DOI":"10.3139\/120.111180","article-title":"Optimization and characterization of friction surfaced coatings of ferrous alloys","volume":"60","author":"Shariq","year":"2018","journal-title":"Mater. Test"},{"key":"ref_30","doi-asserted-by":"crossref","first-page":"860","DOI":"10.1080\/10426914.2015.1048462","article-title":"Modeling and Optimization of Machining Nimonic C-263 Superalloy using Multicut Strategy in WEDM","volume":"31","author":"Mandal","year":"2016","journal-title":"Mater. Manuf. Process"},{"key":"ref_31","doi-asserted-by":"crossref","first-page":"60","DOI":"10.1590\/S0103-64402007000100013","article-title":"Analysis of the relationship between the surface hardness and wear resistance of indirect composites used as veneer materials","volume":"18","author":"Faria","year":"2007","journal-title":"Braz. Dent. J."}],"container-title":["Symmetry"],"original-title":[],"language":"en","link":[{"URL":"https:\/\/www.mdpi.com\/2073-8994\/12\/3\/471\/pdf","content-type":"unspecified","content-version":"vor","intended-application":"similarity-checking"}],"deposited":{"date-parts":[[2025,10,11]],"date-time":"2025-10-11T09:07:24Z","timestamp":1760173644000},"score":1,"resource":{"primary":{"URL":"https:\/\/www.mdpi.com\/2073-8994\/12\/3\/471"}},"subtitle":[],"short-title":[],"issued":{"date-parts":[[2020,3,17]]},"references-count":31,"journal-issue":{"issue":"3","published-online":{"date-parts":[[2020,3]]}},"alternative-id":["sym12030471"],"URL":"https:\/\/doi.org\/10.3390\/sym12030471","relation":{},"ISSN":["2073-8994"],"issn-type":[{"value":"2073-8994","type":"electronic"}],"subject":[],"published":{"date-parts":[[2020,3,17]]}}}